迅维网

标题: 希捷串口7代盘No log 4E on disk [打印本页]

作者: 毅然坚强 时间: 2008-7-2 09:02
标题: 希捷串口7代盘No log 4E on disk
Interface task reset
4096k x 16 buffer detected
PUMA - 1_Disk M-22f 06-01-05 09:44
Head Mask FFFF - Switch to full int.
            Spin Ready
3.42  07-18-05 10:42  4096k x 16 buffer
(P)(H)SATA Reset
Not Interface Age!
AutoRd Err 43 at ffffffff.00.012e
AutoRd Err 43 at ffffffff.00.012e
INVALID Cert Disk Code - ROM Resident Revision Required: 3.42
Command Inactive - No VALID Cert Code Detected

T>N50,,22
T>#
Enter Drive S/N  4MR3VRJ6
Enter Packwriter S/N 4MR3VRJ6
T>Pgm=00 Trk=00000(0E306[0F68E]).0(0).000(000) Zn=0 Err=00 ErCt=0000 Hlth=0000 CHlth=0000 Ready LBA=00000000
Age=50 Type=A8 MxCyl=164F8 MxHd=0 MxSct=44C BSz=2000 TCode=00000000

T>E4E
No log 4E on disk
T>N2,,22
T>No valid SeaDex script in buffer.
Begin Test 02
ASCII logging on

                  Not Power Cycling

Temp Diode 008B
( 27 C )

                  Not Power Cycling
Zones 0-F,  Heads 0-1, adaptives set to defaults
Head Mask FFFF -
Read Bias - Head    0 1 2 3
                  9 9
Head Mask FFFF - Switch to full int.
            Spin Ready
ASCII logging off

Cylinder ID->OD Bias OD->ID Bias
00100       0036       0030
00300       0036       0026
00500       0035       0024
00700       0034       0024
00900       0033       0024
00B00       0034       0024
00D00       0032       0023
00F00       0034       0022
01100       0033       0024
01300       0034       0022
01500       0032       0022
01700       0032       0020
01900       0030       0020
01B00       002F       001F
01D00       002F       0020
01F00       0030       001F
02100       002E       001E
02300       002E       001E
02500       002E       001E
02700       002E       001C
02900       002D       001C
02B00       002D       001C
02D00       002D       001D
02F00       002C       001B
03100       002B       001A
03300       0029       0017
03500       0029       0017
03700       0028       0018
03900       0027       0017
03B00       0027       0018
03D00       0028       0017
03F00       0026       0016
04100       0028       0016
04300       0027       0016
04500       0028       0016
04700       0026       0015
04900       0023       0014
04B00       0024       0014
04D00       0024       0013
04F00       0023       0012
05100       0024       0013
05300       0023       0013
05500       0021       0013
05700       0021       0011
05900       0022       0012
05B00       0023       0011
05D00       0022       0010
05F00       0022       0011
06100       0022       0011
06300       001F       000F
06500       001F       000D
06700       001E       000D
06900       001F       000D
06B00       0020       000C
06D00       001E       000E
06F00       001E       000D
07100       001E       000C
07300       001D       000B
07500       001D       000B
07700       001C       000C
07900       001B       0008
07B00       001B       0009
07D00       001A       0009
07F00       001B       000A
08100       001A       0007
08300       0019       0007
08500       0018       0007
08700       0018       0008
08900       001A       0008
08B00       0019       0008
08D00       0018       0008
08F00       0017       0006
09100       0019       0007
09300       0017       0006
09500       0014       0004
09700       0014       0001
09900       0012       -0001
09B00       0013       0001
09D00       0014       0001
09F00       0015       0003
0A100       0013       0003
0A300       0013       0002
0A500       0014       0001
0A700       0012       0001
0A900       0012       -0001
0AB00       0010       -0003
0AD00       0010       -0002
0AF00       0011       -0003
0B100       0011       -0003
0B300       0012       -0002
0B500       0011       -0002
0B700       0014       -0002
0B900       0012       0000
0BB00       0011       -0001
0BD00       000F       -0005
0BF00       000D       -0006
0C100       000D       -0005
0C300       000F       -0004
0C500       0010       -0004
0C700       000F       -0005
0C900       000F       -0002
0CB00       000E       -0004
0CD00       0010       -0002
0CF00       000E       -0002
0D100       0010       -0002
0D300       0010       -0002
0D500       0011       -0001
0D700       000D       -0003
0D900       0010       -0001
0DB00       0012       -0003
0DD00       0012       -0003
0DF00       0012       0001
0E100       0014       -0001
0E300       0013       0000
0E500       0012       0000
0E700       0013       -0001
0E900       0014       0001
0EB00       0017       0003
0ED00       0019       0003
0EF00       0019       0006
0F100       001B       0007
0F300       001C       0009
0F500       001E       000B
0F700       0020       000C
0F900       0022       000F
0FB00       0024       0011
0FD00       0025       0013
0FF00       002B       0017
10100       002E       001B
10300       0031       001C
10500       0033       0021
10700       0038       0025
10900       003B       0029
10B00       003F       002C
10D00       0043       0030
10F00       004A       0033
11100       004D       003A
11300       0054       003E
11500       0059       0045
11700       0062       004E
11900       0068       0055
11B00       006F       005C
11D00       0076       0062
11F00       007E       006A
12100       0087       0072
12300       0090       007C
12500       009A       0086
12700       00A6       0092
12900       00B1       009E
12B00       00BE       00A8
12D00       00CA       00B5
12F00       00D6       00C2
13100       00E4       00D0
13300       00F3       00DE
13500       0104       00EE
13700       0114       0100
13900       0126       010E
13B00       0135       0122
13D00       014A       0134
13F00       015D       0149
14100       0171       015D
14300       0188       0175
14500       01A0       018B
14700       01B9       01A4
14900       01D4       01BE
14B00       01EC       01D9
14D00       0208       01F1
14F00       0225       0210
15100       0244       022E
15300       0264       024F
15500       0285       0270
15700       02A7       0291
15900       02CB       02B3
15B00       02EF       02DA
15D00       0319       02FF
15F00       0338       0325
16100       0368       034F
16300       0383       037A
16440       03A4       038F

作者: 毅然坚强 时间: 2008-7-2 09:04
ASCII logging on
Ref Trk Tan Timing Skew (h0 to h0) = 0000 servo clocks.
ID-OD Delta Timing Skew (h0 to h0) = 0000 servo clocks.
Ref Trk Tan Timing Skew (h0 to h1) = 188F servo clocks.
ID-OD Delta Timing Skew (h0 to h1) = FFDA servo clocks.
Ref Trk Tan Timing Skew (h0 to h2) = 0000 servo clocks.
ID-OD Delta Timing Skew (h0 to h2) = 0000 servo clocks.
Ref Trk Tan Timing Skew (h0 to h3) = 0000 servo clocks.
ID-OD Delta Timing Skew (h0 to h3) = 0000 servo clocks.
Greycode Index Skew (h0) = 0000 servo sectors.
Greycode Index Skew (h1) = 0000 servo sectors.
Greycode Index Skew (h2) = 0000 servo sectors.
Greycode Index Skew (h3) = 0000 servo sectors.
ASCII logging off
Ref Trk Tan Timing Skew (h0 to h0) = 0000 servo clocks.
ID-OD Delta Timing Skew (h0 to h0) = 0000 servo clocks.
Ref Trk Tan Timing Skew (h0 to h1) = 1892 servo clocks.
ID-OD Delta Timing Skew (h0 to h1) = FFD8 servo clocks.
Ref Trk Tan Timing Skew (h0 to h2) = 0000 servo clocks.
ID-OD Delta Timing Skew (h0 to h2) = 0000 servo clocks.
Ref Trk Tan Timing Skew (h0 to h3) = 0000 servo clocks.
ID-OD Delta Timing Skew (h0 to h3) = 0000 servo clocks.
Greycode Index Skew (h0) = 0000 servo sectors.
Greycode Index Skew (h1) = 0000 servo sectors.
Greycode Index Skew (h2) = 0000 servo sectors.
Greycode Index Skew (h3) = 0000 servo sectors.
ASCII logging on
Calibrating Physical Track 0 on heads 0 thru 1
Finding Maximum Eccentricity ...
Calibrating Head 0 ...
DAC value = FF22

Buzz  - Head Mask FFFF - Switch to full int.
            Spin Ready
Calibrating Head 1 ...

Radial Offset Table:

Head 0 Offset = A99
Head 1 Offset = B00
Head 2 Offset = 1388
Head 3 Offset = 1388

Radial ID Delta Offset Table - RPO:

Head 0 Offset = 0
Head 1 Offset = 0
Head 2 Offset = 0
Head 3 Offset = 0

Ref Trk Tan Timing Skew (h0 to h0) = 0000 servo clocks.
ID-OD Delta Timing Skew (h0 to h0) = 0000 servo clocks.
Ref Trk Tan Timing Skew (h0 to h1) = 1894 servo clocks.
ID-OD Delta Timing Skew (h0 to h1) = FFDD servo clocks.
Ref Trk Tan Timing Skew (h0 to h2) = 0000 servo clocks.
ID-OD Delta Timing Skew (h0 to h2) = 0000 servo clocks.
Ref Trk Tan Timing Skew (h0 to h3) = 0000 servo clocks.
ID-OD Delta Timing Skew (h0 to h3) = 0000 servo clocks.
Greycode Index Skew (h0) = 0000 servo sectors.
Greycode Index Skew (h1) = 0000 servo sectors.
Greycode Index Skew (h2) = 0000 servo sectors.
Greycode Index Skew (h3) = 0000 servo sectors.

Disk 00
RTE Amp = 0040 servo clocks (div by 64). Sector = 00A3h. Trk/2 = B2BFh.
RTE Amp = 0037 servo clocks (div by 64). Sector = 00A5h. Trk/2 = 8F02h.
RTE Amp = 0028 servo clocks (div by 64). Sector = 009Ah. Trk/2 = 6B44h.
RTE Amp = 0023 servo clocks (div by 64). Sector = 0072h. Trk/2 = 4787h.
RTE Amp = 0022 servo clocks (div by 64). Sector = 0085h. Trk/2 = 23C9h.
RTE Amp = 0020 servo clocks (div by 64). Sector = 0088h. Trk/2 = 000Ch.

Disk 01
RTE Amp = 0000 servo clocks (div by 64). Sector = 0000h. Trk/2 = 0000h.
RTE Amp = 0000 servo clocks (div by 64). Sector = 0000h. Trk/2 = 0000h.
RTE Amp = 0000 servo clocks (div by 64). Sector = 0000h. Trk/2 = 0000h.
RTE Amp = 0000 servo clocks (div by 64). Sector = 0000h. Trk/2 = 0000h.
RTE Amp = 0000 servo clocks (div by 64). Sector = 0000h. Trk/2 = 0000h.
RTE Amp = 0000 servo clocks (div by 64). Sector = 0000h. Trk/2 = 0000h.
RPO Calibration!
Calibrating Head 1 ...

Radial Offset Table:

Head 0 Offset = A99
Head 1 Offset = B00
Head 2 Offset = 1388
Head 3 Offset = 1388

Radial ID Delta Offset Table - RPO:

Head 0 Offset = 0
Head 1 Offset = FFFF
Head 2 Offset = F711
Head 3 Offset = F711

Head 00
Zone 00:  00018 - 0132D  1100 (044C) 687.097
Zone 01:  0132E - 03BFE  1045 (0415) 663.594
Zone 02:  03BFF - 05D87  1012 (03F4) 644.516
Zone 03:  05D88 - 07831 990 (03DE) 627.097
Zone 04:  07832 - 09073 953 (03B9) 606.774
Zone 05:  09074 - 0A797 916 (0394) 585.484
Zone 06:  0A798 - 0C72C 880 (0370) 551.613
Zone 07:  0C72D - 0D653 836 (0344) 535.777
Zone 08:  0D654 - 0E8AC 806 (0326) 515.881
Zone 09:  0E8AD - 0FD7A 770 (0302) 491.129
Zone 0A:  0FD7B - 10DD3 733 (02DD) 471.216
Zone 0B:  10DD4 - 1204F 691 (02B3) 448.680
Zone 0C:  12050 - 137F9 660 (0294) 417.339
Zone 0D:  137FA - 145B5 616 (0268) 401.985
Zone 0E:  145B6 - 155F4 586 (024A) 381.567
Zone 0F:  155F5 - 164F8 550 (0226) 357.097

Head 01
Zone 00:  00018 - 0132D  1100 (044C) 687.097
Zone 01:  0132E - 03BFE  1045 (0415) 663.594
Zone 02:  03BFF - 05D87  1012 (03F4) 644.516
Zone 03:  05D88 - 07831 990 (03DE) 627.097
Zone 04:  07832 - 09073 953 (03B9) 606.774
Zone 05:  09074 - 0A797 916 (0394) 585.484
Zone 06:  0A798 - 0C72C 880 (0370) 551.613
Zone 07:  0C72D - 0D653 836 (0344) 535.777
Zone 08:  0D654 - 0E8AC 806 (0326) 515.881
Zone 09:  0E8AD - 0FD7A 770 (0302) 491.129
Zone 0A:  0FD7B - 10DD3 733 (02DD) 471.216
Zone 0B:  10DD4 - 1204F 691 (02B3) 448.680
Zone 0C:  12050 - 137F9 660 (0294) 417.339
Zone 0D:  137FA - 145B5 616 (0268) 401.985
Zone 0E:  145B6 - 155F4 586 (024A) 381.567
Zone 0F:  155F5 - 164F8 550 (0226) 357.097
Reserve:  0EBF5 - 0EC7B 640 (0280) 454.147
Total KBAs = 00000000
EP=1, TA=1, HiGain=1, OTRd=1, Early Rd=0, Splash=1, Reload=1, NPML=1, MRBias=1
Bst/Zap=1, SrvoThrsh=1, RunOut=1, MaxECC=1, ECC 2=1, ECC 1=1, ECC 0=1
Data=FF, Write=80, ID=FF
No entries in Log
All Hds 0-1, All Cyls 00018-164F8, Rnd data

Performing AFC Zone Cal
ACFC Calibration:
         CRRO Orders Prior to Cal: (PES*2)^2
  Cyl.Hd 2 3 4 5 6 7 8 12 24
00018.00 02ad 0064 0004 0001 0002 0002 0001 0001 0005
02000.00 0244 0040 0001 0001 0000 0000 0005 0000 0001
04000.00 0211 0032 0000 0000 0000 0000 000a 0000 0001
06000.00 01e4 001a 0000 0000 0002 0000 0011 0000 0001
08000.00 01b9 0010 0000 0001 0001 0001 0009 0001 0001
0a000.00 0191 000a 0000 0001 0001 0001 0009 0000 0001
0e000.00 0199 0001 0002 0005 0004 0005 0004 0000 0002
10000.00 0199 0002 0004 000d 0010 0001 0005 0001 0001
12000.00 01c9 0001 0005 001d 0010 0002 0002 0002 0002
14000.00 01c9 0004 0008 0028 0025 000d 0001 0001 0002
16000.00 02b4 0004 0008 0044 0049 001d 0001 0010 0001
00018.01 00e1 0089 000a 0000 0004 0001 0001 000a 0002
02000.01 00b9 0068 0005 0001 0000 0001 0005 0002 0002
04000.01 00ca 0055 0005 0000 0001 0000 0002 0000 0001
06000.01 00b5 0035 0004 0004 0001 0000 0005 0000 0001
08000.01 00b5 001d 0001 0001 0001 0000 000a 0000 0001
0a000.01 00b5 0014 0001 0004 0004 0000 0005 0000 0001
0e000.01 00ca 0008 0000 0010 000d 0000 0008 0000 0001
10000.01 00ca 0005 0005 0019 0022 0002 0005 0001 0002
12000.01 00e1 0005 0008 0032 0041 000d 000a 0000 0002
14000.01 00f4 000a 000d 0051 0075 0012 0008 0001 0001
16000.01 0128 0022 0031 0090 0179 0032 000a 0002 0001
EP=0, TA=0, HiGain=0, OTRd=0, Early Rd=0, Splash=0, Reload=0, NPML=0, MRBias=0
Bst/Zap=0, SrvoThrsh=0, RunOut=0, MaxECC=0, ECC 2=1, ECC 1=1, ECC 0=1
Data=02, Write=40, ID=1E
Channel Srvo Table
  Head Addr VGA  SATT  Tap5  Tap6  Tap3  Tap7  Tap2  Tap8  Tap9  XDC
00 A548 80 72 65 88 A4 70 3B 84 80 96
01 A552 80 72 65 88 A4 70 3B 84 80 96
Adapt Servo Zone 09
Adapt Servo 0000f313.00
Adapts Loaded
Rbck DATA load

作者: 毅然坚强 时间: 2008-7-2 09:05
NPML    00
Test 0000f313.00 00009e3d BER 00000001
Adjust ATTR 00 VGAS 3c VGAR 44 FREQR 7e SRVTEST 10
Adjust ATTR 01 VGAS 3d VGAR 74 FREQR 7d within _ATT

MRASYM    80 00009c47 BER 00000002
MRASYM    7d 00009bd2 BER 00000002 update 7d hold
Servo Zone 11, OD [0000D8AA.0,FC5D,025D,C0]
Left Bath = FEF0, Right Bath = FFE7 : Pick (FF6B) ( Min/Max AGC 51FF )
Servo Zone 11, ID [0000EDEF.0,FD09,0309,C0]
Left Bath = FFB4, Right Bath = 0084 : Pick (001C) ( Min/Max AGC 7EFF )
Servo Zone 12, OD [0000EE00.0,FD0A,030A,C0]
Left Bath = FFAF, Right Bath = 0081 : Pick (0018) ( Min/Max AGC 7EFF )
Servo Zone 12, ID [000103CB.0,FDBF,03BF,C0]
Left Bath = 0056, Right Bath = 014B : Pick (00D0) ( Min/Max AGC 52FF )
Test 0000f313.00 0000946a BER 00000fff
Servo Zone  0, OD [00000020.0,F70D,FD0D,C0]
Left Bath = F988, Right Bath = FA73 : Pick (F9FD) ( Min/Max AGC 41FF )
Servo Zone  0, ID [00000067.0,F73C,FD3C,C0]
Left Bath = F982, Right Bath = FA6D : Pick (F9F7) ( Min/Max AGC 43FF )
Servo Zone  1, OD [00000078.0,F744,FD44,C0]
Left Bath = F982, Right Bath = FA69 : Pick (F9F5) ( Min/Max AGC 45FF )
Servo Zone  1, ID [00000759.0,F769,FD69,C0]
Left Bath = F9AD, Right Bath = FA9C : Pick (FA24) ( Min/Max AGC 43FF )
Servo Zone  2, OD [0000076A.0,F76A,FD6A,C0]
Left Bath = F9A1, Right Bath = FA8D : Pick (FA17) ( Min/Max AGC 46FF )
Servo Zone  2, ID [00000E52.0,F787,FD87,C0]
Left Bath = F9CE, Right Bath = FABA : Pick (FA44) ( Min/Max AGC 44FF )
Servo Zone  3, OD [00000E63.0,F788,FD88,C0]
Left Bath = F9BF, Right Bath = FAB2 : Pick (FA38) ( Min/Max AGC 47FF )
Servo Zone  3, ID [00001713.0,F7AF,FDAF,C0]
Left Bath = FA00, Right Bath = FAF3 : Pick (FA79) ( Min/Max AGC 42FF )
Test 0000130d.00 0000d1ea BER 00000fff
Test 0000f313.00 0000980b BER 00000fff
Adjust ATTR 01 VGAS 3d VGAR 77 FREQR 80 within _ATT

MRASYM    7d 0000972b BER 00000fff
MRASYM    89 00009756 BER 00000fff hold
Default Tap Weight 00000000 Settle Tap Weight 00000154
XDCTAP    96 0000587e BER 00000000 adapt
XDCTAP    7f 00005979 BER 00000000 hold

CUTOFF  Lower 021b  Upper 032f  Step 0003  Right 17  Mask 00000008
Default  033a 000059d8 BER 00000000
Floor  1 10 0000c13c 00014a1b
Left 1 0318 0000aaab
Middle 0 0321 00006864
Right  1 032f 000066ad
Lowest 1 032a 00006669
Restore  033a 00005a1d BER 00000000
Update Default Servo Cutoff and Range 033A

SV TAP5 Lower 0020  Upper 00df  Step 0006  Right 1f  Mask 00001000
Default  0065 00005a0a BER 00000000
Floor  1 20 00005f75 00005f75
Left 1 0026 00005822
Middle 1 004f 00005684
Right  1 0079 00005eb5
Lowest 1 0032 00005553
Z = -A1/(2*A2) : FFE0
X = Z + Xavg : FFEF
Curve 00d4 0000659c
New    004f 00005627 BER 00000000
00005627 BER 00000000 _ATT 01 VGAS 3d VGAR 66 FREQR 81 Taps frozen read adapt
Current Tap Weight 00004971 diff ffffb68f tap limits
000055f1 BER 00000000 _ATT 01 VGAS 3e VGAR 61 FREQR 80 Taps frozen read adapt
Current Tap Weight 0000002f diff 00004942 tap limits
000055fd BER 00000000 _ATT 01 VGAS 3d VGAR 67 FREQR 81 Taps frozen read adapt
Current Tap Weight 00000030 diff ffffffff Save servo Force servo update
Rbck Default  DATA load
Test 0000f313.00 00009c5a BER 00000fff
Adapt Servo 0000f313.01
Adapts Loaded
Rbck DATA load

NPML    00
Test 0000f313.01 0000e269 BER 00000004
Adjust ATTR 00 VGAS 6a VGAR 6f FREQR 7f within _ATT

MRASYM    80 0000f229 BER 0000000a
MRASYM    ba 0000bb6d BER 00000006 update ba hold
Servo Zone 11, OD [0000D843.1,FC5D,025D,C0]
Left Bath = FF14, Right Bath = FFDD : Pick (FF78) ( Min/Max AGC 78FF )
Servo Zone 11, ID [0000ED88.1,FD09,0309,C0]
Left Bath = FFCC, Right Bath = 0090 : Pick (002E) ( Min/Max AGC 7CFF )
Servo Zone 12, OD [0000ED99.1,FD0A,030A,C0]
Left Bath = FFCE, Right Bath = 0095 : Pick (0031) ( Min/Max AGC 7EFF )
Servo Zone 12, ID [00010364.1,FDBF,03BF,C0]
Left Bath = 0087, Right Bath = 014E : Pick (00EA) ( Min/Max AGC 7EFF )
Test 0000f313.01 00007131 BER 00000fff
Servo Zone  1, OD [00000020.1,F744,FD44,C0]
Left Bath = F987, Right Bath = FA41 : Pick (F9E4) ( Min/Max AGC 6FFF )
Servo Zone  1, ID [000006F2.1,F769,FD69,C0]
Left Bath = F9AE, Right Bath = FA75 : Pick (FA11) ( Min/Max AGC 68FF )
Servo Zone  2, OD [00000703.1,F76A,FD6A,C0]
Left Bath = F9A7, Right Bath = FA67 : Pick (FA07) ( Min/Max AGC 6CFF )
Servo Zone  2, ID [00000DEB.1,F787,FD87,C0]
Left Bath = F9D9, Right Bath = FA96 : Pick (FA37) ( Min/Max AGC 6FFF )
Servo Zone  3, OD [00000DFC.1,F788,FD88,C0]
Left Bath = F9CC, Right Bath = FA86 : Pick (FA29) ( Min/Max AGC 6FFF )
Servo Zone  3, ID [000016AC.1,F7AF,FDAF,C0]
Left Bath = FA07, Right Bath = FAC7 : Pick (FA67) ( Min/Max AGC 6CFF )
Test 0000130d.01 0000abf7 BER 00000fff
Test 0000f313.01 00006dd8 BER 00000fff
Adjust ATTR 00 VGAS 69 VGAR 6b FREQR 81 within _ATT

MRASYM    ba 00006e9a BER 00000fff
MRASYM    b4 000070a3 BER 00000fff hold
Default Tap Weight 00000000 Settle Tap Weight 00000154
XDCTAP    96 00005db6 BER 00000000 adapt
XDCTAP    7c 00005f91 BER 00000000 hold

CUTOFF  Lower 021b  Upper 032f  Step 0003  Right 17  Mask 00000008
Default  033a 00005ff7 BER 00000000
Floor  1 0f 0000afb2 000123b3
Left 1 0318 0000a850
Middle 0 0321 000074b5
Right  1 032f 0000727b
Lowest 1 032d 0000727b
Restore  033a 0000610d BER 00000000
Update Default Servo Cutoff and Range 033A

SV TAP5 Lower 0020  Upper 00df  Step 0006  Right 1f  Mask 00001000
Default  0065 00006174 BER 00000000
Floor  1 20 00006c6c 00006c6c
Left 1 0032 000063af
Middle 1 005e 00006097
Right  1 008b 000069a8
Lowest 1 004a 00005d08
Z = -A1/(2*A2) : FFFF
X = Z + Xavg : 000E
Curve 0074 0000660e
New    005e 00005ef2 BER 00000000
00005ee8 BER 00000000 _ATT 01 VGAS 6d VGAR 61 FREQR 82 Taps frozen read adapt
Current Tap Weight 00004579 diff ffffba87 tap limits
00005f8b BER 00000000 _ATT 01 VGAS 6f VGAR 61 FREQR 81 Taps frozen read adapt
Current Tap Weight 0000001a diff 0000455f tap limits
00005f47 BER 00000000 _ATT 01 VGAS 6c VGAR 62 FREQR 81 Taps frozen read adapt
Current Tap Weight 0000000e diff 0000000c Save servo Force servo update
Rbck Default  DATA load
Test 0000f313.01 0000817c BER 00000fff

作者: 毅然坚强 时间: 2008-7-2 09:06
HiTemp Bias BackOff Head 0 1 2 3
                        9 9
Media 0000
Adapt Data Zone 00
Test 000009a2.00 0000cc7c BER 00000003
Test 000009a2.00 0000d608 BER 00000003
Adapt Data 000009a2.00
Rbck DATA load

NPML    00
Test 000009a2.00 0000d4a8 BER 00000002
Adjust ATTR 00 VGAS 67 VGAR 31 FREQR 80 SRVTEST 10
Adjust ATTR 01 VGAS 66 VGAR 60 FREQR 82 within _ATT VGAR FREQR

MRASYM    80 0000ce41 BER 00000002
MRASYM    94 0000cba2 BER 00000001 update 94 hold
Test 00000020.00 0000be83 BER 00000001

Servo Zone 00 OD OFST Lower f99d  Upper fa5c  Step 0006  Right 1f  Mask 00004340
Default  f9fd 0000c4b5 BER 00000003
Floor  1 1f 00031db2 00031db2
Left 1 f9c7 00030aaa
Middle 1 fa05 0000c150
Right  1 fa44 00031506
Lowest 1 fa09 0000b9fd
Z = -A1/(2*A2) : 359A
X = Z + Xavg : 35A9
Curve fa51 00060f72
New    fa05 0000bda7 BER 00000000 AUTO
Test 00000067.00 0000b502 BER 00000000

Servo Zone 00 ID OFST Lower f997  Upper fa56  Step 0006  Right 1f  Mask 00008340
Default  f9f7 0000bb51 BER 00000000
Floor  1 20 00033954 00033954
Left 1 f9c1 0002c9a5
Middle 1 f9ff 0000b8de
Right  1 fa3e 000257dd
Lowest 1 fa03 0000b2ca
Z = -A1/(2*A2) : FBD8
X = Z + Xavg : FBE7
Curve fa4b 00054eac
New    f9ff 0000b4b3 BER 00000000 AUTO
Test 00000078.00 0000c722 BER 00000000

Servo Zone 01 OD OFST Lower f995  Upper fa54  Step 0006  Right 1f  Mask 00004340
Default  f9f5 0000c0ba BER 00000000
Floor  1 1c 000310cb 000310cb
Left 1 f9cb 00027d8e
Middle 1 fa03 0000b3b8
Right  1 fa3c 0002e8b0
Lowest 1 fa07 0000af71
Z = -A1/(2*A2) : 0000
X = Z + Xavg : 000F
Curve f9ef 0000d55f
New    fa03 0000b48c BER 00000000 AUTO
Test 00000759.00 0000c275 BER 00000001

Servo Zone 01 ID OFST Lower f9c4  Upper fa83  Step 0006  Right 1f  Mask 00008340
Default  fa24 0000c8b7 BER 00000001
Floor  1 1e 00040f1d 00040f1d
Left 1 f9fa 0003f1ce
Middle 1 fa35 0000bcdd
Right  1 fa71 00033c52
Lowest 1 fa30 0000bcdd
Z = -A1/(2*A2) : 0000
X = Z + Xavg : 000F
Curve fa1e 0000dddb
New    fa35 0000c272 BER 00000003 AUTO
Test 0000076a.00 0000be88 BER 00000000

Servo Zone 02 OD OFST Lower f9b7  Upper fa76  Step 0006  Right 1f  Mask 00004340
Default  fa17 0000c0bc BER 00000000
Floor  1 1d 000385ef 000385ef
Left 1 f9f3 0002f8f3
Middle 1 fa2b 0000bf5b
Right  1 fa64 0003497e
Lowest 1 fa1d 0000ba36
Z = -A1/(2*A2) : 0000
X = Z + Xavg : 000F
Curve fa11 0000e30f
New    fa2b 0000c38f BER 00000000
Test 00000e52.00 0000c6ad BER 00000001

Servo Zone 02 ID OFST Lower f9e4  Upper faa3  Step 0006  Right 1f  Mask 00008340
Default  fa44 0000bec2 BER 00000000
Floor  1 1d 0003a537 0003a537
Left 1 fa1a 0002eaa9
Middle 1 fa55 0000bda3
Right  1 fa91 0003988d
Lowest 1 fa50 0000bda3
Z = -A1/(2*A2) : 0000
X = Z + Xavg : 000F
Curve fa3e 0000cd82
New    fa55 0000c394 BER 00000001
Test 00000e63.00 0000ccb0 BER 00000003

Servo Zone 03 OD OFST Lower f9d8  Upper fa97  Step 0006  Right 1f  Mask 00004340
Default  fa38 0000c362 BER 00000000
Floor  1 1c 0003728a 0003728a
Left 1 fa14 0002b4c7
Middle 1 fa4c 0000bf6c
Right  1 fa85 0002d041
Lowest 1 fa44 0000bde7
Z = -A1/(2*A2) : 0000
X = Z + Xavg : 000F
Curve fa32 0000e479
New    fa4c 0000c58c BER 00000001
Adjust ATTR 01 VGAS 64 VGAR 5c FREQR 81 within _ATT VGAR FREQR
Test 000009a2.00 0000c660 BER 00000000
Noise target  00000000
Rbck Noise OFF
Rbck DATA save

WRITE_I Lower 0003  Upper 001b  Step 0001  Right 18  Mask 00000342
Default  000e 0000db90 BER 00000002
Floor  1 0e 0000dc44 0000e0ac
Left 1 0009 0000dbf5
Middle 1 000f 0000da9e
Right  1 0016 0000d9d0
Lowest 1 000b 0000d708
Z = -A1/(2*A2) : 0000
X = Z + Xavg : 000C
Curve 000f 0000da9e
New    000f 0000ec4a BER 00000003
Test 000009a2.00 0000be3c BER 00000000

MRASYM    94 0000be2b BER 00000001
MRASYM    8d 0000bce9 BER 00000000 update 8d hold

PRECOMP Lower 0000  Upper 000a  Step 0001  Right 0a  Mask 00000004
Default  0003 0000c014 BER 00000000
Floor  1 0b 0000ca8e 0000e0e9
Left 1 0000 0000ca8e
Middle 1 0002 0000ca06
Right  1 0004 0000c987
Lowest 1 0001 0000bb66
Z = -A1/(2*A2) : FFFC
X = Z + Xavg : 0001
Curve 0001 0000bb66
New    0002 0000bc2a BER 00000000
Test 000009a2.00 0000bcac BER 00000001
XDCTAP    96 0000c23b BER 00000000 adapt
XDCTAP    69 0000c319 BER 00000001 hold

CUTOFF  Lower 0514  Upper 0538  Step 0002  Right 12  Mask 00000348
Default  052c 0004fa9d BER 00000001
Floor  1 0f 0005017f 00052462
Left 1 0522 0004e513
Middle 1 0528 0004f183
Right  1 0530 0004ff33
Lowest 1 0524 0004dda5
New    0528 0004f717 BER 00000000 AUTO

BOOST Lower 0000  Upper 0016  Step 0001  Right 16  Mask 00000360
Default  000b 00050f3c BER 00000000
Floor  1 17 00054726 0005effa
Left 1 0000 00054726
Middle 1 0006 000521d8
Right  1 000c 00052465
Lowest 1 0009 0004fee4
Z = -A1/(2*A2) : FFFD
X = Z + Xavg : 0008
Curve 0008 000510ba
New    0006 0004d9fe BER 00000000 AUTO

TAPDELT Lower 0000  Upper 000f  Step 0001  Right 0f  Mask 00000350
Default  000b 0004fe99 BER 00000000
Floor  1 10 0005a3f8 0006e40a
Left 1 0007 00057d3b
Middle 1 000b 0004f2f5
Right  1 000f 0005a3f8
Lowest 1 000b 0004f2f5
Z = -A1/(2*A2) : 0004
X = Z + Xavg : 000B
Curve 000b 0004f2f5
New    000b 0004ffd6 BER 00000000

作者: 毅然坚强 时间: 2008-7-2 09:06
Servo Zone 00 OD OFST Lower f9a5  Upper fa64  Step 0006  Right 1f  Mask 00004340
Default  fa05 0000bd81 BER 00000000
Floor  1 20 00035bcd 00035bcd
Left 1 f9c9 0002dbbb
Middle 1 fa07 0000bddf
Right  1 fa46 00032d61
Lowest 1 fa05 0000bddf
Z = -A1/(2*A2) : 1EC4
X = Z + Xavg : 1ED3
Curve fa59 00095b36
New    fa07 0000c2b2 BER 00000000

Servo Zone 00 ID OFST Lower f99f  Upper fa5e  Step 0006  Right 1f  Mask 00008340
Default  f9ff 0000be00 BER 00000000
Floor  1 20 0003099d 0003099d
Left 1 f9c3 00027389
Middle 1 fa01 0000b93f
Right  1 fa40 00029463
Lowest 1 fa05 0000b7db
Z = -A1/(2*A2) : FBD6
X = Z + Xavg : FBE5
Curve fa53 0007ee71
New    fa01 0000bfab BER 00000000

Servo Zone 01 OD OFST Lower f9a3  Upper fa62  Step 0006  Right 1f  Mask 00004340
Default  fa03 0000bbe3 BER 00000000
Floor  1 1f 00042bc5 00042bc5
Left 1 f9c7 0003178f
Middle 1 fa02 0000c5bc
Right  1 fa3e 000380f6
Lowest 1 fa09 0000bc5d
Z = -A1/(2*A2) : 6252
X = Z + Xavg : 6261
Curve fa57 000e154d
New    fa02 0000bd79 BER 00000001

Servo Zone 01 ID OFST Lower f9d5  Upper fa94  Step 0006  Right 1f  Mask 00008340
Default  fa35 0000ca7c BER 00000001
Floor  1 1f 0004226e 0004226e
Left 1 f9f9 0003d49c
Middle 1 fa37 0000c7ce
Right  1 fa76 00040db3
Lowest 1 fa2f 0000c21e
Z = -A1/(2*A2) : 2B01
X = Z + Xavg : 2B10
Curve fa89 000df0d1
New    fa37 0000ca22 BER 00000000 AUTO

Servo Zone 02 OD OFST Lower f9cb  Upper fa8a  Step 0006  Right 1f  Mask 00004340
Default  fa2b 0000ca26 BER 00000000
Floor  1 1e 0003d99e 0003d99e
Left 1 f9ef 00036ecb
Middle 1 fa2a 0000c03d
Right  1 fa66 0003a9bd
Lowest 1 fa25 0000c03d
Z = -A1/(2*A2) : 0000
X = Z + Xavg : 000F
Curve fa25 0000c03d
New    fa2a 0000c618 BER 00000000 AUTO

Servo Zone 02 ID OFST Lower f9f5  Upper fab4  Step 0006  Right 1f  Mask 00008340
Default  fa55 0000ce3a BER 00000000
Floor  1 1d 0003af08 0003af08
Left 1 fa19 0003157c
Middle 1 fa54 0000cd9e
Right  1 fa90 00031c41
Lowest 1 fa55 0000c9a4
Z = -A1/(2*A2) : 0000
X = Z + Xavg : 000F
Curve fa4f 0000cd9e
New    fa54 0000c8f8 BER 00000001 AUTO

Servo Zone 03 OD OFST Lower f9ec  Upper faab  Step 0006  Right 1f  Mask 00004340
Default  fa4c 0000ca62 BER 00000001
Floor  1 1c 00037742 00037742
Left 1 fa16 0002bfca
Middle 1 fa4e 0000d13a
Right  1 fa87 0002ea95
Lowest 1 fa40 0000c530
Z = -A1/(2*A2) : 0000
X = Z + Xavg : 000F
Curve fa46 0000ce8a
New    fa4e 0000c9bb BER 00000000 AUTO

CUTOFF  Lower 0522  Upper 0530  Step 0001  Right 0e  Mask 00000348
Default  0528 00050540 BER 00000001
Floor  1 07 00050883 00051760
Left 1 0524 0004ffa3
Middle 1 0528 00050921
Right  1 052c 0004faee
Lowest 1 052c 0004faee
New    0528 000527ab BER 00000000

BOOST Lower 0000  Upper 000d  Step 0001  Right 0d  Mask 00000360
Default  0006 0004f4a0 BER 00000001
Floor  1 0e 00051043 00051b48
Left 1 0000 00051043
Middle 1 0004 0004f829
Right  1 0009 00050bf8
Lowest 1 0006 0004e21c
Z = -A1/(2*A2) : FFFF
X = Z + Xavg : 0005
Curve 0005 0004fdf7
New    0004 000502b1 BER 00000001

TAPDELT Lower 0000  Upper 000f  Step 0001  Right 0f  Mask 00000350
Default  000b 0004ec91 BER 00000000
Floor  1 10 0005b1a2 000712e7
Left 1 0009 0005a620
Middle 1 000c 000520a2
Right  1 000f 0005b1a2
Lowest 1 000b 00050430
Z = -A1/(2*A2) : 0004
X = Z + Xavg : 000B
Curve 000b 00050430
New    000c 0004f1c4 BER 00000001
Noise target  00000000
Rbck Noise OFF
Adjust ATTR 01 VGAS 67 VGAR 70 FREQR 7f within _ATT VGAR FREQR

MRASYM    8d 0000c119 BER 00000003
MRASYM    8d 0000bb3f BER 00000005 update 8d adapt
Test 000009a2.00 0000b786 BER 00000000

MRASYM    8d 0000bac0 BER 00000001
MRASYM    7a 0000b2c4 BER 00000001 update 7a hold

NPML    03 0000b529 BER 00000000 NPML update
NPML    03 0001f2c3 BER 00000000

MRASYM    7a 0001f695 BER 00000001
MRASYM    7e 0001f1f6 BER 00000000 update 7e adapt
BETTER UPDATE TAPS Rbck DATA save
Media 0000
Test 000009a2.01 0000b093 BER 00000000
Test 000009a2.01 0000acbf BER 00000000
Adapt Data 000009a2.01
Rbck DATA load

NPML    00
Test 000009a2.01 0000b3f2 BER 00000000
Adjust ATTR 00 VGAS 9a VGAR 55 FREQR 7f within _ATT VGAR FREQR

MRASYM    80 0000d55d BER 00000002
MRASYM    cb 0000b2c3 BER 00000000 update cb hold
Test 00000020.01 0000ada5 BER 00000002

Servo Zone 01 OD OFST Lower f984  Upper fa43  Step 0006  Right 1f  Mask 00004340
Default  f9e4 0000aff3 BER 00000000
Floor  1 1d 0003610c 0003610c
Left 1 f9b4 00033a00
Middle 1 f9f2 0000a94f
Right  1 fa31 0002885d
Lowest 1 f9f0 0000a94f
Z = -A1/(2*A2) : 0000
X = Z + Xavg : 000F
Curve f9de 0000c4e5
New    f9f2 0000ad54 BER 00000000 AUTO
Test 000006f2.01 0000a7f0 BER 00000000

Servo Zone 01 ID OFST Lower f9b1  Upper fa70  Step 0006  Right 1f  Mask 00008340
Default  fa11 0000a6fb BER 00000000
Floor  1 1d 00030702 00030702
Left 1 f9e7 00025416
Middle 1 fa22 0000a5de
Right  1 fa5e 0002503a
Lowest 1 fa23 0000a357
Z = -A1/(2*A2) : 0000
X = Z + Xavg : 000F
Curve fa0b 0000b6f8
New    fa22 0000a9ec BER 00000001
Test 00000703.01 0000b308 BER 00000002

Servo Zone 02 OD OFST Lower f9a7  Upper fa66  Step 0006  Right 1f  Mask 00004340
Default  fa07 0000ac85 BER 00000000
Floor  1 1b 00029001 00029001
Left 1 f9e3 0002324b
Middle 1 fa1b 0000aca0
Right  1 fa54 00027a65
Lowest 1 fa13 0000a4e0
Z = -A1/(2*A2) : 0947
X = Z + Xavg : 0956
Curve fa5b 0004a0bf
New    fa1b 0000a6c4 BER 00000000 AUTO
Test 00000deb.01 0000a81b BER 00000000

Servo Zone 02 ID OFST Lower f9d7  Upper fa96  Step 0006  Right 1f  Mask 00008340
Default  fa37 0000a859 BER 00000000
Floor  1 1c 0002d544 0002d544
Left 1 fa07 000242b0
Middle 1 fa3f 0000b0a1
Right  1 fa78 000233c5
Lowest 1 fa43 0000a9b2
Z = -A1/(2*A2) : FCF0
X = Z + Xavg : FCFF
Curve fa8b 008db224
New    fa3f 0000a91c BER 00000000
Test 00000dfc.01 0000b3ad BER 00000000

Servo Zone 03 OD OFST Lower f9c9  Upper fa88  Step 0006  Right 1f  Mask 00004340
Default  fa29 0000b276 BER 00000002
Floor  1 1b 0002bd9e 0002bd9e
Left 1 fa05 0002330e
Middle 1 fa3a 0000b11b
Right  1 fa70 00020050
Lowest 1 fa3b 0000ac39
Z = -A1/(2*A2) : 0000
X = Z + Xavg : 000F
Curve fa23 0000cda3
New    fa3a 0000ae05 BER 00000000 AUTO
Adjust ATTR 00 VGAS 99 VGAR 57 FREQR 7d within _ATT VGAR FREQR
Test 000009a2.01 0000a7d7 BER 00000000
Noise target  00000000
Rbck Noise OFF
Rbck DATA save

WRITE_I Lower 0003  Upper 001b  Step 0001  Right 18  Mask 00000342
Default  000e 0000c288 BER 00000000
Floor  1 0f 0000be73 0000c5a2
Left 1 0011 0000bde0
Middle 1 0016 0000bc1e
Right  1 001b 0000bd6a
Lowest 1 0012 0000b7d7
Z = -A1/(2*A2) : 0009
X = Z + Xavg : 0015
Curve 0018 0000bdda
New    0016 0000c10f BER 00000002 AUTO
Test 000009a2.01 0000a0a0 BER 00000001

MRASYM    cb 00009f06 BER 00000000
MRASYM    be 00009f41 BER 00000000 hold

PRECOMP Lower 0000  Upper 000a  Step 0001  Right 0a  Mask 00000004
Default  0003 0000a614 BER 00000000
Floor  1 0b 000095b8 0000be7e
Left 1 0000 000095b8
Middle 1 0000 000095b8
Right  1 0000 000095b8
Lowest 1 0000 000095b8
Z = -A1/(2*A2) : FFFA
X = Z + Xavg : FFFF
Curve 0009 0000edd0
New    0000 0000950f BER 00000001
Test 000009a2.01 000094ee BER 00000000
XDCTAP    96 00009c24 BER 00000000 adapt
XDCTAP    68 00009b66 BER 00000000 hold

CUTOFF  Lower 0514  Upper 0538  Step 0002  Right 12  Mask 00000348
Default  052c 0004a3ae BER 00000000
Floor  1 0e 000496cf 000502ab
Left 1 0522 000487b1
Middle 1 052c 00048707
Right  1 0538 00048847
Lowest 1 0532 00048404
New    052c 00049ba4 BER 00000000 AUTO

BOOST Lower 0000  Upper 0016  Step 0001  Right 16  Mask 00000360
Default  000b 00049a41 BER 00000000
Floor  1 17 00053e60 00053e60
Left 1 0005 000533dd
Middle 1 000b 0004a67e
Right  1 0011 00051d5e
Lowest 1 000c 00049cf6
Z = -A1/(2*A2) : 0000
X = Z + Xavg : 000B
Curve 000b 0004a67e
New    000b 0004a55a BER 00000001

TAPDELT Lower 0000  Upper 000f  Step 0001  Right 0f  Mask 00000350
Default  000b 0004b619 BER 00000000
Floor  1 10 0004e6dd 0005f302
Left 1 0007 0004b1c5
Middle 1 000b 0004981c
Right  1 000f 0004e6dd
Lowest 1 000d 0004874f
Z = -A1/(2*A2) : 0005
X = Z + Xavg : 000C
Curve 000c 00048ca9
New    000b 0004ac52 BER 00000000 AUTO

Servo Zone 01 OD OFST Lower f992  Upper fa51  Step 0006  Right 1f  Mask 00004340
Default  f9f2 0000ac26 BER 00000000
Floor  1 1f 0003fe13 0003fe13
Left 1 f9b6 000378c8
Middle 1 f9f4 0000b258
Right  1 fa33 00030699
Lowest 1 f9f8 0000b1f9
Z = -A1/(2*A2) : FFFF
X = Z + Xavg : 000E
Curve f9e6 0000bbda
New    f9f4 0000b31e BER 00000001

Servo Zone 01 ID OFST Lower f9c2  Upper fa81  Step 0006  Right 1f  Mask 00008340
Default  fa22 0000b5bb BER 00000000
Floor  1 1f 0003b632 0003b632
Left 1 f9e0 00038c95
Middle 1 fa21 0000af7f
Right  1 fa63 000340f8
Lowest 1 fa1c 0000af7f
Z = -A1/(2*A2) : 25E0
X = Z + Xavg : 25EF
Curve fa76 000c5048
New    fa21 0000ae3d BER 00000001 AUTO

Servo Zone 02 OD OFST Lower f9bb  Upper fa7a  Step 0006  Right 1f  Mask 00004340
Default  fa1b 0000b789 BER 00000002
Floor  1 1d 00035f33 00035f33
Left 1 f9df 00032430
Middle 1 fa1a 0000b21b
Right  1 fa56 0002f3a0
Lowest 1 fa0f 0000b00b
Z = -A1/(2*A2) : 0000
X = Z + Xavg : 000F
Curve fa15 0000b21b
New    fa1a 0000b4ff BER 00000000 AUTO

Servo Zone 02 ID OFST Lower f9df  Upper fa9e  Step 0006  Right 1f  Mask 00008340
Default  fa3f 0000ac5d BER 00000000
Floor  1 1f 0003c285 0003c285
Left 1 fa03 00031ebf
Middle 1 fa41 0000af6b
Right  1 fa80 0002f4c0
Lowest 1 fa3f 0000af6b
Z = -A1/(2*A2) : F10E
X = Z + Xavg : F11D
Curve fa93 000ad81a
New    fa41 0000b0ab BER 00000000

作者: 毅然坚强 时间: 2008-7-2 09:07
Servo Zone 03 OD OFST Lower f9da  Upper fa99  Step 0006  Right 1f  Mask 00004340
Default  fa3a 0000b5d8 BER 00000001
Floor  1 1c 00030134 00030134
Left 1 fa04 00021a4d
Middle 1 fa3c 0000b190
Right  1 fa75 0002d869
Lowest 1 fa3a 0000b190
Z = -A1/(2*A2) : 0000
X = Z + Xavg : 000F
Curve fa34 0000b1b9
New    fa3c 0000b449 BER 00000000 AUTO

CUTOFF  Lower 0522  Upper 0538  Step 0001  Right 16  Mask 00000348
Default  052c 0004b295 BER 00000000
Pgm=02 Trk=009A2(009A2[0149C]).1(1).000(42E) Zn=0 Err=00 ErCt=0000 Hlth=0000 CHlth=0000 Ready LBA=005206D4
Floor  1 0c 00049f33 0004a93b
Left 1 0523 000498de
Middle 1 052d 0004b20f
Right  1 0538 00049679
Lowest 1 0538 00049679
New    052d 0004a2fd BER 00000000 AUTO

BOOST Lower 0004  Upper 0012  Step 0001  Right 0e  Mask 00000360
Default  000b 0004a70d BER 00000000
Floor  1 0f 0004f088 0004f088
Left 1 0008 0004c2d4
Middle 1 000b 00049af9
Right  1 000f 0004cda2
Lowest 1 000b 00049af9
Z = -A1/(2*A2) : 0000
X = Z + Xavg : 0007
Curve 000b 00049af9
New    000b 0004a740 BER 00000000

TAPDELT Lower 0000  Upper 000f  Step 0001  Right 0f  Mask 00000350
Default  000b 0004aad6 BER 00000000
Floor  1 10 000504a7 0006021d
Left 1 0007 0004b9c6
Middle 1 000b 0004b404
Right  1 000f 000504a7
Lowest 1 000c 00048764
Z = -A1/(2*A2) : 0005
X = Z + Xavg : 000C
Curve 000c 00048764
New    000b 0004ab04 BER 00000000
Noise target  00000000
Rbck Noise OFF
Adjust ATTR 00 VGAS 99 VGAR 5d FREQR 83 within _ATT VGAR FREQR

MRASYM    cb 00009dd9 BER 00000001
MRASYM    b3 0000a221 BER 00000000 adapt
Test 000009a2.01 00009305 BER 00000000

MRASYM    cb 00009387 BER 00000000
MRASYM    c3 000095d7 BER 00000000 hold

NPML    03 00009510 BER 00000000 NPML update
NPML    03 000127fe BER 00000000

MRASYM    cb 000124a1 BER 00000000
MRASYM    bf 0001234d BER 00000000 update bf adapt
BETTER UPDATE TAPS Rbck DATA save
Media 0000
Adapt Servo Zone 09
Adapt Servo 0000f313.00
Adapts Loaded
Rbck DATA load

NPML    00
Test 0000f313.00 0000951b BER 00000002
Adjust ATTR 00 VGAS 5f VGAR 42 FREQR 7f SRVTEST 10
Adjust ATTR 01 VGAS 60 VGAR 73 FREQR 81 within _ATT

MRASYM    80 00009800 BER 00000005
MRASYM    7b 000097dd BER 00000001 update 7b hold
Test 0000f313.00 0000957c BER 00000000
Test 0000130d.00 000201b2 BER 00000000

RDBIAS  Lower 0001  Upper 0009  Step 0001  Right 08  Mask 00002000
Default  0009 00020f6d BER 00000000
Adjust 0001 0003eeac BER 00000010
Adjust 0002 000374b4 BER 00000003
Adjust 0003 00030832 BER 00000004
Adjust 0004 0002ced6 BER 00000001
Adjust 0005 00028ad9 BER 00000000
Adjust 0006 00025b1b BER 00000000
Adjust 0007 00024555 BER 00000000
Adjust 0008 00021ea8 BER 00000002
Adjust 0009 0002100c BER 00000000
Floor  1 09 0002100c 0002bb27
Left 1 0009 0002100c
Middle 1 0009 0002100c
Right  1 0009 0002100c
Lowest 1 0009 0002100c
Z = -A1/(2*A2) : 0004
X = Z + Xavg : 0008
Curve 0008 00021ea8
New    0009 00020778 BER 00000000
RdBias Upper 0009 Lower 0001 Step 0001
SPT 044c Revs 00de
RdBias 09 VGAR 6e Rbt 09.0 OTF 09.0 Raw 07.2
RdBias 08 VGAR 77 Rbt 09.0 OTF 09.0 Raw 07.2
RdBias 07 VGAR 80 Rbt 09.0 OTF 09.0 Raw 07.2
RdBias 06 VGAR 8a Rbt 09.0 OTF 09.0 Raw 06.9
RdBias 05 VGAR 94 Rbt 09.0 OTF 09.0 Raw 06.9
RdBias 04 VGAR 9f Rbt 09.0 OTF 09.0 Raw 06.7
RdBias 03 VGAR a8 Rbt 09.0 OTF 09.0 Raw 06.5
RdBias 02 VGAR b4 Rbt 09.0 OTF 09.0 Raw 06.1
RdBias 01 VGAR c0 Rbt 09.0 OTF 09.0 Raw 05.7
RdBias 07 VGAR 80 Rbt 09.0 OTF 09.0 Raw 07.0
Test 0000f313.00 0000a2dc BER 00000000
Adjust ATTR 01 VGAS 71 VGAR 87 FREQR 83 within _ATT

MRASYM    7b 00009f5d BER 00000002
MRASYM    94 000098f4 BER 00000002 update 94 hold
Default Tap Weight 00000000 Settle Tap Weight 00000154
XDCTAP    96 0000609b BER 00000000 adapt
XDCTAP    80 0000633d BER 00000000 hold

CUTOFF  Lower 021b  Upper 032f  Step 0003  Right 17  Mask 00000008
Default  033a 00006486 BER 00000000
Floor  1 0e 0000c7c9 00016ab5
Left 1 031b 0000a2c8
Middle 0 0324 000075b4
Right  1 032f 00007728
Lowest 1 032a 00007439
Restore  033a 0000684b BER 00000000
Update Default Servo Cutoff and Range 033A

SV TAP5 Lower 0020  Upper 00df  Step 0006  Right 1f  Mask 00001000
Default  0065 00006687 BER 00000000
Floor  1 20 0000626c 000069e6
Left 1 0020 0000626c
Middle 1 0043 00005ebd
Right  1 0067 000061cf
Lowest 1 004a 00005e07
Z = -A1/(2*A2) : FFFF
X = Z + Xavg : 000E
Curve 0074 000066ca
New    0043 00005cec BER 00000000
00005cdf BER 00000000 _ATT 01 VGAS 6e VGAR 7c FREQR 81 Taps frozen read adapt
Current Tap Weight 0000540e diff ffffabf2 tap limits
00005d81 BER 00000000 _ATT 01 VGAS 6f VGAR 7a FREQR 80 Taps frozen read adapt
Current Tap Weight 0000000c diff 00005402 tap limits
00005d0a BER 00000000 _ATT 01 VGAS 6d VGAR 7c FREQR 81 Taps frozen read adapt
Current Tap Weight 00000006 diff 00000006 Save servo Force servo update
Rbck Default  DATA load
Test 0000f313.00 00009f3d BER 00000fff
Adapt Servo 0000f313.01
Adapts Loaded
Rbck DATA load

NPML    00
Test 0000f313.01 00007db1 BER 00000000
Adjust ATTR 00 VGAS 8c VGAR 6e FREQR 80 within _ATT

MRASYM    80 000080d7 BER 00000001
MRASYM    b3 00006e39 BER 00000000 update b3 hold
Test 0000f313.01 00007085 BER 00000000
Test 0000130d.01 000121e0 BER 00000000

RDBIAS  Lower 0001  Upper 0009  Step 0001  Right 08  Mask 00002000
Default  0009 00012432 BER 00000000
Adjust 0001 0002c4e3 BER 00000004
Adjust 0002 00024cf2 BER 00000002
Adjust 0003 0001ec3f BER 00000001
Adjust 0004 0001b6c4 BER 00000001
Adjust 0005 00018534 BER 00000000
Adjust 0006 00017115 BER 00000000
Adjust 0007 0001529d BER 00000000
Adjust 0008 00013dd0 BER 00000000
Adjust 0009 00012e07 BER 00000000
Floor  1 09 00012e07 0001b665
Left 1 0009 00012e07
Middle 1 0009 00012e07
Right  1 0009 00012e07
Lowest 1 0009 00012e07
Z = -A1/(2*A2) : 0003
X = Z + Xavg : 0007
Curve 0008 00013dd0
New    0009 00012aa8 BER 00000000
RdBias Upper 0009 Lower 0001 Step 0001
SPT 044c Revs 00de
RdBias 09 VGAR 5b Rbt 09.0 OTF 09.0 Raw 08.0
RdBias 08 VGAR 61 Rbt 09.0 OTF 09.0 Raw 07.8
RdBias 07 VGAR 66 Rbt 09.0 OTF 09.0 Raw 07.7
RdBias 06 VGAR 6d Rbt 09.0 OTF 09.0 Raw 07.3
RdBias 05 VGAR 75 Rbt 09.0 OTF 09.0 Raw 07.1
RdBias 04 VGAR 7d Rbt 09.0 OTF 09.0 Raw 06.8
RdBias 03 VGAR 83 Rbt 09.0 OTF 09.0 Raw 06.6
RdBias 02 VGAR 8b Rbt 09.0 OTF 09.0 Raw 06.0
RdBias 01 VGAR 94 Rbt 09.0 OTF 09.0 Raw 05.7
RdBias 05 VGAR 75 Rbt 09.0 OTF 09.0 Raw 07.1
Test 0000f313.01 0000801d BER 00000000
Adjust ATTR 00 VGAS a9 VGAR 86 FREQR 80 within _ATT

MRASYM    b3 0000831f BER 00000002
MRASYM    ae 0000834b BER 00000000 hold
Default Tap Weight 00000000 Settle Tap Weight 00000154
XDCTAP    96 00006648 BER 00000000 adapt
XDCTAP    7c 00006945 BER 00000000 hold

CUTOFF  Lower 021b  Upper 032f  Step 0003  Right 17  Mask 00000008
Default  033a 00006a63 BER 00000000
Floor  1 0d 0000b66a 0001268a
Left 1 031b 00009ba2
Middle 0 0324 000080d7
Right  1 032f 00007eeb
Lowest 1 032d 00007eeb
Restore  033a 00006a6d BER 00000000
Update Default Servo Cutoff and Range 033A

SV TAP5 Lower 0020  Upper 00df  Step 0006  Right 1f  Mask 00001000
Default  0065 000069f3 BER 00000000
Floor  1 20 000077f6 000077f6
Left 1 0032 00006b7e
Middle 1 005e 00006986
Right  1 008b 000075a2
Lowest 1 0044 000064e2
Z = -A1/(2*A2) : FFEC
X = Z + Xavg : FFFB
Curve 00d4 000086a5
New    005e 00006977 BER 00000000
00006a4f BER 00000000 _ATT 01 VGAS a7 VGAR 7d FREQR 82 Taps frozen read adapt
Current Tap Weight 0000424d diff ffffbdb3 tap limits
00006a17 BER 00000000 _ATT 01 VGAS aa VGAR 80 FREQR 81 Taps frozen read adapt
Current Tap Weight 00000012 diff 0000423b tap limits
00006a4d BER 00000000 _ATT 01 VGAS ac VGAR 7f FREQR 80 Taps frozen read adapt
Current Tap Weight 00000012 diff 00000000 Save servo Force servo update
Rbck Default  DATA load
Test 0000f313.01 0000934c BER 00000fff

作者: 毅然坚强 时间: 2008-7-2 09:07
HiTemp Bias BackOff Head 0 1 2 3
                        9 9
Media 0000
Channel Srvo Table
  Head Addr VGA  SATT  Tap5  Tap6  Tap3  Tap7  Tap2  Tap8  Tap9  XDC
00 A548 7C 72 43 C8 51 79 9A 9D 72 96
01 A552 7F 72 5E BB 56 88 99 93 7E 96

Performing Servo Cals, view results in log 3
ASCII logging off

Cylinder ID->OD Bias OD->ID Bias
00100       0033       002D
00300       0033       0025
00500       0031       0022
00700       002F       0022
00900       0030       0022
00B00       002F       0020
00D00       002F       0021
00F00       002D       001F
01100       002C       001E
01300       002D       001D
01500       002B       001D
01700       002B       001D
01900       002C       001D
01B00       002C       001D
01D00       002B       001C
01F00       002A       001B
02100       002A       001A
02300       0029       0019
02500       0028       0019
02700       0028       0019
02900       0027       0018
02B00       0028       0017
02D00       0027       0019
02F00       0025       0017
03100       0025       0015
03300       0026       0016
03500       0027       0017
03700       0025       0015
03900       0024       0015
03B00       0024       0012
03D00       0022       0012
03F00       0024       0011
04100       0022       0013
04300       0022       0013
04500       0021       0011
04700       0021       0010
04900       0021       0010
04B00       0020       0011
04D00       0020       0010
04F00       0020       000F
05100       001F       000E
05300       001E       000E
05500       001D       000D
05700       001E       000E
05900       001C       000D
05B00       001D       000D
05D00       001C       000C
05F00       001B       000B
06100       001B       000C
06300       001C       000A
06500       001B       000A
06700       001A       000A
06900       001A       000A
06B00       001A       000A
06D00       0019       0009
06F00       0017       0007
07100       0018       0008
07300       0017       0006
07500       0018       0008
07700       0018       0007
07900       0016       0006
07B00       0018       0005
07D00       0016       0006
07F00       0015       0004
08100       0015       0005
08300       0013       0005
08500       0012       0002
08700       0013       0004
08900       0012       0002
08B00       0011       0002
08D00       0011       -0001
08F00       0010       0001
09100       0012       0000
09300       0012       0001
09500       0012       0002
09700       0010       0000
09900       0011       -0001
09B00       0011       0000
09D00       0011       0000
09F00       000D       -0003
0A100       000B       -0005
0A300       000C       -0005
0A500       000C       -0005
0A700       000D       -0003
0A900       000D       -0003
0AB00       000D       -0005
0AD00       000D       -0004
0AF00       000B       -0004
0B100       000D       -0005
0B300       000A       -0005
0B500       0008       -0008
0B700       0009       -0008
0B900       0009       -0008
0BB00       000A       -0007
0BD00       000A       -0006
0BF00       000A       -0005
0C100       000B       -0005
0C300       000B       -0006
0C500       0009       -0006
0C700       0006       -0008
0C900       0005       -0009
0CB00       0006       -0009
0CD00       0008       -0009
0CF00       0008       -0008
0D100       0008       -0008
0D300       0009       -0007
0D500       0007       -000A
0D700       0006       -0009
0D900       0009       -0009
0DB00       0008       -0006
0DD00       000A       -0008
0DF00       0007       -0009
0E100       0009       -0007
0E300       0008       -0006
0E500       000A       -0007
0E700       0009       -0008
0E900       000C       -0007
0EB00       000D       -0004
0ED00       000D       -0004
0EF00       000E       -0003
0F100       0010       -0004
0F300       000F       -0001
0F500       0010       -0002
0F700       0011       0001
0F900       0013       0003
0FB00       0015       0001
0FD00       0018       0004
0FF00       0019       0006
10100       001B       0009
10300       001C       000A
10500       001F       000C
10700       0021       0010
10900       0025       0013
10B00       0027       0017
10D00       002C       0019
10F00       002E       001D
11100       0033       0021
11300       0036       0024
11500       003A       0028
11700       003E       002E
11900       0044       0032
11B00       0049       0037
11D00       004F       003E
11F00       0056       0044
12100       005C       004A
12300       0063       0051
12500       006C       0058
12700       0070       0060
12900       007A       006A
12B00       0085       0072
12D00       008F       007C
12F00       0098       0087
13100       00A5       0091
13300       00B0       009E
13500       00BC       00A9
13700       00C9       00B8
13900       00D4       00C3
13B00       00E5       00D1
13D00       00F3       00E2
13F00       0104       00F1
14100       0115       0102
14300       0126       0111
14500       0139       0125
14700       0150       0139
14900       0161       014E
14B00       0177       0162
14D00       018C       0178
14F00       01A5       0191
15100       01BF       01AA
15300       01D8       01C4
15500       01F1       01DF
15700       020E       01FA
15900       022D       0218
15B00       024C       0239
15D00       026C       0259
15F00       028D       027A
16100       02AD       029B
16300       02CE       02C1
16440       02E2       02D7
Head Linearizing
Cyl = 00B2CB
Head = 00 Gain Adjust = 0113
Head = 01 Gain Adjust = 010A
Head Linearizing
Cyl = 0002D4
Head = 00 Gain Adjust = 010C
Head = 01 Gain Adjust = 00FF
Head Linearizing
Cyl = 0162C3
Head = 00 Gain Adjust = 00F6
Head = 01 Gain Adjust = 00E7

CYL = 003C0 KA = 4990 scaled by 4000  CYL = 00BC0 KA = 4790 scaled by 4000
CYL = 013C0 KA = 46D0 scaled by 4000  CYL = 01BC0 KA = 4600 scaled by 4000
CYL = 023C0 KA = 4570 scaled by 4000  CYL = 02BC0 KA = 44A0 scaled by 4000
CYL = 033C0 KA = 4410 scaled by 4000  CYL = 03BC0 KA = 43C0 scaled by 4000
CYL = 043C0 KA = 4360 scaled by 4000  CYL = 04BC0 KA = 4360 scaled by 4000
CYL = 0B2CB KA = 4400 scaled by 4000
CYL = 11940 KA = 4330 scaled by 4000  CYL = 12140 KA = 4330 scaled by 4000
CYL = 12940 KA = 4340 scaled by 4000  CYL = 13140 KA = 4380 scaled by 4000
CYL = 13940 KA = 43A0 scaled by 4000  CYL = 14140 KA = 43F0 scaled by 4000
CYL = 14940 KA = 4480 scaled by 4000  CYL = 15140 KA = 4540 scaled by 4000
CYL = 15940 KA = 4640 scaled by 4000  CYL = 16140 KA = 4760 scaled by 4000

作者: 毅然坚强 时间: 2008-7-2 09:08
Head Linearizing
Cyl = 00B2CB
Head = 00 Gain Adjust = 0111
Head = 01 Gain Adjust = 010A
Head Linearizing
Cyl = 0002D4
Head = 00 Gain Adjust = 0109
Head = 01 Gain Adjust = 0100
Head Linearizing
Cyl = 0162C3
Head = 00 Gain Adjust = 00F6
Head = 01 Gain Adjust = 00E7
Table Linearization in Process
Head Gain Measure
Head Max  -38h  -28h  -18h  -08h  +08h  +18h  +28h  +38h
00  5A9D  41A5  3D1D  3CCF  4214  4F05  5A9D  5884  4D9D
01  50A8  4BE3  50A8  508D  4CC9  4CF6  4E11  4AEF  4B10
Normalized Integrated Gain
Head  -40h  -30h  -20h  -10h 00 +10h  +20h  +30h  +40h
00  0000  02E5  0597  0846  0B30  0EAC  12AB  1693  1A00
01  0000  03C3  07C2  0BC0  0F8E  135F  173E  1AF5  1EAD
PES to Position Table
Head  -40h  -30h  -20h  -10h 00 +10h  +20h  +30h  +40h
00  FFC0  FFCE  FFDC  FFE9  FFF7  0008  001C  002F  0040
01  FFC0  FFD0  FFE0  FFF1  0001  0011  0021  0030  0040
ASCII logging on
Calibrating Physical Track 0 on heads 0 thru 1
Finding Maximum Eccentricity ...
Calibrating Head 0 ...
DAC value = FF22

Buzz  - Head Mask FFFF - Switch to full int.
            Spin Ready
Calibrating Head 1 ...

Radial Offset Table:

Head 0 Offset = AA5
Head 1 Offset = B0C
Head 2 Offset = 1388
Head 3 Offset = 1388

Radial ID Delta Offset Table - RPO:

Head 0 Offset = 0
Head 1 Offset = FFFF
Head 2 Offset = F711
Head 3 Offset = F711

Ref Trk Tan Timing Skew (h0 to h0) = 0000 servo clocks.
ID-OD Delta Timing Skew (h0 to h0) = 0000 servo clocks.
Ref Trk Tan Timing Skew (h0 to h1) = 1898 servo clocks.
ID-OD Delta Timing Skew (h0 to h1) = FFDE servo clocks.
Ref Trk Tan Timing Skew (h0 to h2) = 0000 servo clocks.
ID-OD Delta Timing Skew (h0 to h2) = 0000 servo clocks.
Ref Trk Tan Timing Skew (h0 to h3) = 0000 servo clocks.
ID-OD Delta Timing Skew (h0 to h3) = 0000 servo clocks.
Greycode Index Skew (h0) = 0000 servo sectors.
Greycode Index Skew (h1) = 0000 servo sectors.
Greycode Index Skew (h2) = 0000 servo sectors.
Greycode Index Skew (h3) = 0000 servo sectors.

Disk 00
RTE Amp = 003D servo clocks (div by 64). Sector = 00A7h. Trk/2 = B2BFh.
RTE Amp = 0033 servo clocks (div by 64). Sector = 009Bh. Trk/2 = 8F02h.
RTE Amp = 002A servo clocks (div by 64). Sector = 0097h. Trk/2 = 6B44h.
RTE Amp = 0029 servo clocks (div by 64). Sector = 00A5h. Trk/2 = 4787h.
RTE Amp = 0025 servo clocks (div by 64). Sector = 008Ch. Trk/2 = 23C9h.
RTE Amp = 0021 servo clocks (div by 64). Sector = 0086h. Trk/2 = 000Ch.

Disk 01
RTE Amp = 0000 servo clocks (div by 64). Sector = 0000h. Trk/2 = 0000h.
RTE Amp = 0000 servo clocks (div by 64). Sector = 0000h. Trk/2 = 0000h.
RTE Amp = 0000 servo clocks (div by 64). Sector = 0000h. Trk/2 = 0000h.
RTE Amp = 0000 servo clocks (div by 64). Sector = 0000h. Trk/2 = 0000h.
RTE Amp = 0000 servo clocks (div by 64). Sector = 0000h. Trk/2 = 0000h.
RTE Amp = 0000 servo clocks (div by 64). Sector = 0000h. Trk/2 = 0000h.
RPO Calibration!
Calibrating Head 1 ...

Radial Offset Table:

Head 0 Offset = AA5
Head 1 Offset = B0C
Head 2 Offset = 1388
Head 3 Offset = 1388

Radial ID Delta Offset Table - RPO:

Head 0 Offset = 0
Head 1 Offset = FFFF
Head 2 Offset = EE2E
Head 3 Offset = EE2E

Servo Zone 11, OD [0000D89E.0,FC6B,026B,C0]
Left Bath = FEF7, Right Bath = FFDF : Pick (FF6B) ( Min/Max AGC 63FF )
Servo Zone 11, ID [0000EDE3.0,FD1B,031B,C0]
Left Bath = FFA8, Right Bath = 0090 : Pick (001C) ( Min/Max AGC 66FF )
Servo Zone 12, OD [0000EDF4.0,FD18,0318,C0]
Left Bath = FFAE, Right Bath = 0091 : Pick (001F) ( Min/Max AGC 60FF )
Servo Zone 12, ID [000103BF.0,FDCF,03CF,C0]
Left Bath = 0066, Right Bath = 0146 : Pick (00D6) ( Min/Max AGC 66FF )
Servo Zone 11, OD [0000D837.1,FC78,0278,C0]
Left Bath = FF2D, Right Bath = FFCD : Pick (FF7D) ( Min/Max AGC 99FF )
Servo Zone 11, ID [0000ED7C.1,FD2D,032D,C0]
Left Bath = FFDE, Right Bath = 007E : Pick (002E) ( Min/Max AGC 98FF )
Servo Zone 12, OD [0000ED8D.1,FD31,0331,C0]
Left Bath = FFDC, Right Bath = 0084 : Pick (0030) ( Min/Max AGC 98FF )
Servo Zone 12, ID [00010358.1,FDE9,03E9,C0]
Left Bath = 009C, Right Bath = 0136 : Pick (00E9) ( Min/Max AGC 9BFF )
Adapt Data Zone 09
Test 0000f313.00 00005a0c BER 00000000
Test 0000f313.00 00005a04 BER 00000000
Adapt Data 0000f313.00
Rbck DATA load

NPML    00
Test 0000f313.00 000056cb BER 00000000
Adjust ATTR 00 VGAS 74 VGAR 43 FREQR 7e SRVTEST 10
Adjust ATTR 01 VGAS 75 VGAR 6f FREQR 7f within _ATT VGAR FREQR

MRASYM    80 000057c4 BER 00000000
MRASYM    8a 000056ed BER 00000001 update 8a hold
Test 0000ede3.00 00005431 BER 00000000

Servo Zone 11 ID OFST Lower ffbc  Upper 007b  Step 0006  Right 1f  Mask 00008340
Default  001c 000053d1 BER 00000000
Floor  1 20 00020009 00020009
Left 1 ffe0 0001d045
Middle 1 0024 000055c5
Right  1 0069 0001dd0b
Lowest 1 0016 00005437
Z = -A1/(2*A2) : 9D08
X = Z + Xavg : 9D17
Curve 0070 00043540
New    0024 0000570e BER 00000000
Test 0000edf4.00 000054b3 BER 00000000

Servo Zone 12 OD OFST Lower ffbf  Upper 007e  Step 0006  Right 1f  Mask 00004340
Default  001f 00005759 BER 00000000
Floor  1 20 0002100b 0002100b
Left 1 ffe3 00017ae3
Middle 1 0024 00005709
Right  1 0066 0001cef1
Lowest 1 0019 000056c2
Z = -A1/(2*A2) : EABB
X = Z + Xavg : EACA
Curve 0073 0005d00f
New    0024 000058f8 BER 00000000
Adjust ATTR 01 VGAS 78 VGAR 74 FREQR 7e within _ATT VGAR FREQR
Test 0000f313.00 000059c3 BER 00000000
Noise target  00000000
Rbck Noise OFF
Rbck DATA save

WRITE_I Lower 0003  Upper 001b  Step 0001  Right 18  Mask 00000342
Default  000e 00006294 BER 00000000
Floor  1 0e 00005d24 00006013
Left 1 0012 00005b72
Middle 1 0016 00005dad
Right  1 001b 00005b66
Lowest 1 0018 00005b26
Z = -A1/(2*A2) : 000B
X = Z + Xavg : 0017
Curve 001a 00005e4a
New    0016 00005aa2 BER 00000000 AUTO
Test 0000f313.00 0000574b BER 00000000

MRASYM    8a 00005582 BER 00000000
MRASYM    8f 000054f4 BER 00000000 update 8f hold

PRECOMP Lower 0000  Upper 000a  Step 0001  Right 0a  Mask 00000004
Default  0005 0000573d BER 00000000
Floor  1 0b 00005d64 00005d64
Left 1 0002 00005c4c
Middle 1 0004 00005578
Right  1 0007 00005ac2
Lowest 1 0005 00005461
Z = -A1/(2*A2) : 0000
X = Z + Xavg : 0005
Curve 0005 00005461
New    0004 0000564e BER 00000000
Test 0000f313.00 000058a2 BER 00000000
XDCTAP    96 00005660 BER 00000000 adapt
XDCTAP    6d 000056a7 BER 00000000 hold

CUTOFF  Lower 041c  Upper 0510  Step 0002  Right 14  Mask 00000348
Default  043c 0004858e BER 00000000
Floor  1 0e 00049f4f 0004d4d0
Left 1 042c 00049e8b
Middle 1 0436 0004a1a2
Right  1 050c 00048e4e
Lowest 1 0430 0004866b
New    0436 00049dca BER 00000000

BOOST Lower 0000  Upper 0016  Step 0001  Right 16  Mask 00000360
Default  000d 0004f5a7 BER 00000000
Floor  1 17 0005768e 0005768e
Left 1 0007 00056f2f
Middle 1 000d 0004f5d5
Right  1 0013 00057252
Lowest 1 000e 0004edd2
Z = -A1/(2*A2) : 0001
X = Z + Xavg : 000C
Curve 000c 000509c5
New    000d 000498a7 BER 00000000 AUTO

TAPDELT Lower 0000  Upper 000f  Step 0001  Right 0f  Mask 00000350
Default  000b 0004a68c BER 00000000
Floor  1 10 00055c86 0005a520
Left 1 0005 00053b93
Middle 1 000a 0004ade5
Right  1 000f 00055c86
Lowest 1 000b 00048bd6
Z = -A1/(2*A2) : 0003
X = Z + Xavg : 000A
Curve 000a 0004ade5
New    000a 0004be72 BER 00000000

Servo Zone 11 ID OFST Lower ffc4  Upper 0083  Step 0006  Right 1f  Mask 00008340
Default  0024 00005f58 BER 00000000
Floor  1 20 000218bd 000218bd
Left 1 ffe2 0001cbd3
Middle 1 0023 00005e53
Right  1 0065 0001b1e9
Lowest 1 0018 00005e4c
Z = -A1/(2*A2) : 4C00
X = Z + Xavg : 4C0F
Curve 0078 0006fcb0
New    0023 00005e70 BER 00000002 AUTO

Servo Zone 12 OD OFST Lower ffc4  Upper 0083  Step 0006  Right 1f  Mask 00004340
Default  0024 00005e2c BER 00000000
Floor  1 20 000226c4 000226c4
Left 1 ffe2 0001c050
Middle 1 0023 00005ca6
Right  1 0065 0001c603
Lowest 1 001e 00005ca6
Z = -A1/(2*A2) : EFE0
X = Z + Xavg : EFEF
Curve 0078 00078d64
New    0023 00005da1 BER 00000000 AUTO

CUTOFF  Lower 042c  Upper 050c  Step 0001  Right 14  Mask 00000348
Default  0436 0004b422 BER 00000000
Floor  1 0b 0004a5ad 0004b291
Left 1 042c 0004a56d
Middle 1 0431 00049a69
Right  1 0437 0004a1cf
Lowest 1 042d 00049a20
New    0431 0004a5d7 BER 00000000 AUTO

BOOST Lower 0006  Upper 0014  Step 0001  Right 0e  Mask 00000360
Default  000d 0004a5f6 BER 00000000
Floor  1 0f 0004eb09 0004eb09
Left 1 0009 0004e426
Middle 1 000d 0004a786
Right  1 0011 0004d66f
Lowest 1 000e 00049a48
Z = -A1/(2*A2) : 0000
X = Z + Xavg : 0007
Curve 000d 0004a786
New    000d 0004addf BER 00000000

TAPDELT Lower 0000  Upper 000f  Step 0001  Right 0f  Mask 00000350
Default  000a 0004a96d BER 00000000
Floor  1 10 00058f0c 0005a9c7
Left 1 0005 00052039
Middle 1 000a 0004c759
Right  1 000f 00058f0c
Lowest 1 000b 00048f96
Z = -A1/(2*A2) : 0002
X = Z + Xavg : 0009
Curve 0009 0004df25
New    000a 0004be43 BER 00000000
Noise target  00000000
Rbck Noise OFF
Adjust ATTR 01 VGAS 75 VGAR 77 FREQR 80 within _ATT VGAR FREQR

MRASYM    8f 00005fa0 BER 00000000
MRASYM    9c 00005f65 BER 00000002 update 9c adapt
Test 0000f313.00 00005cb3 BER 00000000

MRASYM    9c 00005cca BER 00000000
MRASYM    98 00005c5d BER 00000000 update 98 hold

NPML    03 00005d01 BER 00000002 NPML update
NPML    03 0000b216 BER 00000000

MRASYM    98 0000b085 BER 00000000
MRASYM    99 0000ad22 BER 00000000 update 99 adapt
UPDATE TAPS Rbck DATA save
Media 0000
Test 0000f313.01 000057b8 BER 00000000
Test 0000f313.01 000056a7 BER 00000000
Adapt Data 0000f313.01

作者: 毅然坚强 时间: 2008-7-2 09:09
Rbck DATA load

NPML    00
Test 0000f313.01 0000553a BER 00000000
Adjust ATTR 00 VGAS aa VGAR 7b FREQR 80 within _ATT VGAR FREQR

MRASYM    80 00006443 BER 00000000
MRASYM    b7 000055d1 BER 00000000 update b7 hold
Test 0000ed7c.01 000051d0 BER 00000002

Servo Zone 11 ID OFST Lower ffce  Upper 008d  Step 0006  Right 1f  Mask 00008340
Default  002e 000050a9 BER 00000000
Floor  1 20 0001d67a 0001d67a
Left 1 ffec 0001d22f
Middle 1 0030 000052ef
Right  1 0075 00017824
Lowest 1 0034 00005279
Z = -A1/(2*A2) : FFFF
X = Z + Xavg : 000E
Curve 0022 0000580f
New    0030 000053e5 BER 00000000
Test 0000ed8d.01 0000514f BER 00000000

Servo Zone 12 OD OFST Lower ffd0  Upper 008f  Step 0006  Right 1f  Mask 00004340
Default  0030 00004fee BER 00000000
Floor  1 1f 00018838 00018838
Left 1 fff4 0001374e
Middle 1 0032 000054d9
Right  1 0071 000122d3
Lowest 1 002a 00005421
Z = -A1/(2*A2) : 0010
X = Z + Xavg : 001F
Curve 0084 000463ae
New    0032 000053af BER 00000000
Adjust ATTR 00 VGAS ab VGAR 76 FREQR 81 within _ATT VGAR FREQR
Test 0000f313.01 000057f7 BER 00000000
Noise target  00000000
Rbck Noise OFF
Rbck DATA save

WRITE_I Lower 0003  Upper 001b  Step 0001  Right 18  Mask 00000342
Default  000e 00005959 BER 00000000
Floor  1 0e 000058a0 00005c40
Left 1 0016 00005759
Middle 1 0018 000056cc
Right  1 001b 0000556f
Lowest 1 001b 0000556f
Z = -A1/(2*A2) : 0026
X = Z + Xavg : 0032
Curve 001a 000055b6
New    0018 00005891 BER 00000000 AUTO
Test 0000f313.01 000053b4 BER 00000000

MRASYM    b7 00005153 BER 00000000
MRASYM    b5 000051b8 BER 00000000 hold

PRECOMP Lower 0000  Upper 000a  Step 0001  Right 0a  Mask 00000004
Default  0005 00005312 BER 00000000
Floor  1 0b 00005095 0000567b
Left 1 0000 00005095
Middle 1 0002 00004d5c
Right  1 0004 00004f58
Lowest 1 0002 00004d5c
Z = -A1/(2*A2) : FFFE
X = Z + Xavg : 0003
Curve 0003 00004f3b
New    0002 000050f8 BER 00000000
Test 0000f313.01 00004de3 BER 00000000
XDCTAP    96 00004e2f BER 00000000 adapt
XDCTAP    6d 00004dff BER 00000000 hold

CUTOFF  Lower 041c  Upper 0510  Step 0002  Right 14  Mask 00000348
Default  043c 000455d6 BER 00000000
Floor  1 0f 00045d22 0004a3eb
Left 1 042e 00044861
Middle 1 0438 00045501
Right  1 050e 00045aab
Lowest 1 0432 0004422b
New    0438 00045609 BER 00000000

BOOST Lower 0000  Upper 0016  Step 0001  Right 16  Mask 00000360
Default  000d 0004a37e BER 00000000
Floor  1 17 00052053 00052053
Left 1 000a 000503f5
Middle 1 000f 00047c5a
Right  1 0015 0005165c
Lowest 1 0010 000474e2
Z = -A1/(2*A2) : 0005
X = Z + Xavg : 0010
Curve 0010 000474e2
New    000f 00045829 BER 00000000 AUTO

TAPDELT Lower 0000  Upper 000f  Step 0001  Right 0f  Mask 00000350
Default  000b 00045803 BER 00000000
Floor  1 10 00050e6b 0005486b
Left 1 0005 0004bea8
Middle 1 000a 00046772
Right  1 000f 00050e6b
Lowest 1 0008 00043eaa
Z = -A1/(2*A2) : 0003
X = Z + Xavg : 000A
Curve 000a 00046772
New    000a 00046290 BER 00000000

Servo Zone 11 ID OFST Lower ffd0  Upper 008f  Step 0006  Right 1f  Mask 00008340
Default  0030 00005ab9 BER 00000000
Floor  1 20 0001e817 0001e817
Left 1 ffee 0001b047
Middle 1 0032 00005a97
Right  1 0077 0001da10
Lowest 1 0036 000058a0
Z = -A1/(2*A2) : AC00
X = Z + Xavg : AC0F
Curve 0084 0004b1a7
New    0032 0000593f BER 00000002 AUTO

Servo Zone 12 OD OFST Lower ffd2  Upper 0091  Step 0006  Right 1f  Mask 00004340
Default  0032 00005d93 BER 00000000
Floor  1 20 0001df30 0001df30
Left 1 fff0 00019546
Middle 1 0031 00005b03
Right  1 0073 00017edf
Lowest 1 0032 000057cd
Z = -A1/(2*A2) : D800
X = Z + Xavg : D80F
Curve 0086 00052ab3
New    0031 00005a85 BER 00000000 AUTO

CUTOFF  Lower 042e  Upper 050e  Step 0001  Right 14  Mask 00000348
Default  0438 000472d8 BER 00000000
Floor  1 0c 00046778 00046c89
Left 1 042e 000466fb
Middle 1 0437 0004711b
Right  1 050d 000466f4
Lowest 1 042f 00045f1b
New    0437 000472f3 BER 00000000

BOOST Lower 0009  Upper 0016  Step 0001  Right 0d  Mask 00000360
Default  000f 0004cf5e BER 00000000
Floor  1 0e 0005151b 0005151b
Left 1 000d 00050d18
Middle 1 0010 0004bb38
Right  1 0014 0004f767
Lowest 1 0010 0004bb38
Z = -A1/(2*A2) : 0001
X = Z + Xavg : 0007
Curve 0010 0004bb38
New    0010 00046f63 BER 00000000 AUTO

TAPDELT Lower 0000  Upper 000f  Step 0001  Right 0f  Mask 00000350
Default  000a 00047a1e BER 00000000
Floor  1 10 000543c2 00054412
Left 1 0005 0004ae5a
Middle 1 000a 00046faf
Right  1 000f 000543c2
Lowest 1 0007 00044131
Z = -A1/(2*A2) : 0003
X = Z + Xavg : 000A
Curve 000a 00046faf
New    000a 0004742a BER 00000000 AUTO
Noise target  00000000
Rbck Noise OFF
Adjust ATTR 00 VGAS ab VGAR 74 FREQR 81 within _ATT VGAR FREQR

MRASYM    b7 000056c8 BER 00000000
MRASYM    b8 00005517 BER 00000000 update b8 adapt
Test 0000f313.01 00004fe4 BER 00000000

MRASYM    b8 0000545b BER 00000000
MRASYM    b8 000050d6 BER 00000000 update b8 hold

NPML    03 0000514e BER 00000001 NPML update
NPML    03 0000abc9 BER 00000000

MRASYM    b8 0000b350 BER 00000000
MRASYM    b9 0000ae81 BER 00000000 update b9 adapt
BETTER UPDATE TAPS Rbck DATA save
Media 0000

作者: 毅然坚强 时间: 2008-7-2 09:09
Performing AFC Zone Cal

Performing ACFC Cal
ASCII logging off
ACFC Calibration:
         CRRO Orders Prior to Cal: (PES*2)^2
  Cyl.Hd 2 3 4 5 6 7 8 12 24
00018.00 01e5 0041 0000 0001 0000 0000 000a 0000 0004
02000.00 01e4 0031 0000 0001 0001 0000 0005 0001 0001
04000.00 01b9 0025 0000 0000 0001 0000 0004 0000 0004
06000.00 01b9 001a 0000 0000 0001 0000 0005 0000 0001
08000.00 0191 0011 0000 0000 0001 0000 0005 0000 0001
0a000.00 0194 000a 0000 0001 0001 0000 0001 0001 0001
0e000.00 0172 0002 0002 0005 0004 0000 0004 0000 0001
10000.00 0179 0001 0005 0005 0009 0001 0001 0000 0001
12000.00 0179 0001 0005 0014 001a 0005 0004 0000 0001
14000.00 01a0 0004 0008 001a 001a 000a 0001 0001 0001
16000.00 022a 0004 0005 0028 0028 001a 0000 0005 0001
00018.01 00b4 0068 0004 0000 0000 0001 0005 0002 0002
02000.01 00aa 0044 0004 0000 0001 0000 0005 0000 0001
04000.01 0095 0032 0001 0000 0001 0000 0001 0000 0002
06000.01 00a4 0025 0001 0001 0001 0000 0005 0000 0002
08000.01 0091 001a 0000 0004 0001 0001 0002 0000 0002
0a000.01 00a2 0011 0001 0004 0001 0000 0002 0001 0002
0e000.01 00b5 0005 0002 0010 0008 0000 0005 0000 0002
10000.01 00b5 0008 0008 0019 0019 0005 0005 0000 0002
12000.01 00ca 0005 0005 0032 002d 0005 0005 0000 0001
14000.01 00ca 0005 0009 0040 0064 0012 0005 0000 0001
16000.01 00f4 0019 0019 0064 00e1 0022 0009 0001 0001
ASCII logging on
EP=0, TA=0, HiGain=0, OTRd=0, Early Rd=0, Splash=0, Reload=0, NPML=0, MRBias=0
Bst/Zap=0, SrvoThrsh=0, RunOut=0, MaxECC=0, ECC 2=0, ECC 1=0, ECC 0=1
Data=05, Write=60, ID=1E
0071 Entries:
_____Head___0______  _____Head___1______
43 0EC28.0A2 0A2 01
43 0EC28.0E9 0EA 01
43 0EC28.070 070 01
43 0EC28.044 044 01
43 0EC28.085 087 01
43 0EC28.0D4 0D8 01
43 0EC28.10D 113 01
43 0EC28.12A 131 01
43 0EC28.14F 157 01
59 0EC28.14F 157 01
43 0EC29.164 164 01
43 0EC29.1CB 1CC 01
43 0EC29.240 242 01
43 0EC2B.02F 02F 01
43 0EC2B.13D 13E 01
43 0EC2C.02A 02A 01
43 0EC2C.031 032 01
43 0EC2C.052 054 01
43 0EC2C.05C 05F 01
43 0EC2C.070 074 01
43 0EC2C.077 07C 01
43 0EC2C.087 08D 01
43 0EC2C.09B 0A2 01
43 0EC2C.0BF 0C7 01
59 0EC2C.0BF 0C7 01
43 0EC2D.21E 21E 01
43 0EC2D.02A 02A 01
43 0EC2D.031 032 01
43 0EC2D.24D 250 01
43 0EC2D.20E 210 01
43 0EC2E.014 014 01
43 0EC2E.095 096 01
43 0EC2E.0BE 0C0 01
43 0EC2E.11C 11F 01
43 0EC2E.0F7 0FA 01
43 0EC2E.195 19A 01
43 0EC2E.1F4 1FA 01
43 0EC2E.217 21E 01
43 0EC2F.12D 12D 01
43 0EC2F.14F 150 01
43 0EC30.150 150 01
43 0EC30.12D 12D 01
43 0EC35.1C4 1C4 01
43 0EC36.0D9 0D9 01
43 0EC36.171 172 01
43 0EC36.19A 19C 01
43 0EC36.1C1 1C4 01
43 0EC36.1D2 1D6 01
43 0EC36.18A 18C 01
43 0EC37.012 012 01
43 0EC37.088 089 01
43 0EC37.0B4 0B6 01
43 0EC37.0D6 0D9 01
43 0EC37.15E 162 01
43 0EC37.07F 080 01
43 0EC37.0E6 0EB 01
43 0EC37.175 17C 01
43 0EC37.184 18C 01
59 0EC37.184 18C 01
43 0EC38.012 012 01
43 0EC38.051 052 01
43 0EC38.06C 06E 01
43 0EC38.07D 080 01
43 0EC38.0B2 0B6 01
43 0EC38.0C7 0CC 01
43 0EC38.0D3 0D9 01
43 0EC38.0E4 0EB 01
43 0EC38.12C 134 01
59 0EC38.12C 134 01
43 0EC39.052 052 01
43 0EC39.06D 06E 01
43 0EC39.0B4 0B6 01
43 0EC39.074 076 01
43 0EC39.012 012 01
43 0EC39.0E6 0EB 01
43 0EC39.12E 134 01
43 0EC39.185 18C 01
43 0EC39.1C5 1CD 01
59 0EC39.1C5 1CD 01
43 0EC3A.1DB 1DB 01
43 0EC3A.052 052 01
43 0EC3A.138 139 01
43 0EC3A.26C 26F 01
43 0EC3B.008 008 01
43 0EC3B.002 002 01
43 0EC3B.022 024 01
43 0EC3B.037 03A 01
43 0EC3B.094 098 01
43 0EC3B.108 10D 01
43 0EC3B.183 189 01
43 0EC3B.1D4 1DB 01
43 0EC3B.095 09A 01
59 0EC3B.095 09A 01
43 0EC3C.002 002 01
43 0EC3C.007 008 01
43 0EC3C.01A 01C 01
43 0EC3C.021 024 01
43 0EC3C.036 03A 01
43 0EC3C.05E 063 01
43 0EC3C.0AA 0B0 01
43 0EC3C.044 049 01
43 0EC3C.0C3 0CB 01
59 0EC3C.0C3 0CB 01
43 0EC3D.008 008 01
43 0EC3D.01B 01C 01
43 0EC3D.061 063 01
43 0EC3D.07D 080 01
43 0EC3D.0AC 0B0 01
43 0EC3D.159 15E 01
43 0EC3D.08E 092 01
43 0EC3D.1AE 1B5 01
43 0EC3D.19B 1A2 01
59 0EC3D.19B 1A2 01


ASCII logging off
EP=0, TA=0, HiGain=1, OTRd=0, Early Rd=0, Splash=1, Reload=1, NPML=1, MRBias=1
Bst/Zap=1, SrvoThrsh=1, RunOut=1, MaxECC=1, ECC 2=1, ECC 1=1, ECC 0=1
Data=40, Write=40, ID=1E

                        Power Cycling
EP=1, TA=1, HiGain=1, OTRd=1, Early Rd=0, Splash=1, Reload=1, NPML=1, MRBias=1
Bst/Zap=1, SrvoThrsh=1, RunOut=1, MaxECC=1, ECC 2=1, ECC 1=1, ECC 0=1
Data=FF, Write=80, ID=FF
ASCII logging on
(SN: 4MR3VRJ6)
.PW 4MR3VRJ6
ASCII logging off
.088
Channel Srvo Table
  Head Addr VGA  SATT  Tap5  Tap6  Tap3  Tap7  Tap2  Tap8  Tap9  XDC
00 A548 7C 72 43 C8 51 79 9A 9D 72 96
01 A552 7F 72 5E BB 56 88 99 93 7E 96
DC Erasing zero Offset tracks
Skipping MDW oversample s/n cylinders.
Unable to write SeaDex script to disc.

                        Power Cycling
AbEnd Test 02
Begin Test 4D
ASCII logging on

                  Not Power Cycling
ASCII logging off
ASCII logging on
Fail Log Summary .....
Cum Health = 2000
Log 01 - Health 2000
Log 02 - Health 2000
Head Mask FFFF -
Read Bias - Head    0 1 2 3
                  9 9
Switch to full int.
            Spin Ready

=====================================================================
No log on disk

=====================================================================
Scanning Log 8 .... No log on disk

=====================================================================
Scanning Log 31 .... No log on disk

=====================================================================
Scanning Log 32 .... No log on disk

=====================================================================
Scanning Log 33 .... No log on disk

=====================================================================
Scanning Log 34 .... No log on disk

=====================================================================
Scanning Log 3A .... No log on disk

=====================================================================

=====================================================================

作者: 毅然坚强 时间: 2008-7-2 09:10
Head #Defect #Align radial defect(%)  EC59 EC60
User Slip Defect List
Close slip list

Error Close Slip List 59
0    000001d          .             .    .
User Slip Defect List
Close slip list

Error Close Slip List 59
1    000001d          .             .    .

=====================================================================

                        Power Cycling
ASCII logging off
OkEnd Test 4D
Begin Test 39
ASCII logging on
ASCII logging off
OkEnd Test 39
Begin Test 22
ASCII logging on

                  Not Power Cycling
No log on disk
The average VGA amplitude for zone 0 head 0 is 9B.
The delta of VGA amplitudes for Zone 0 head 0 exceeds the limit (14)
The average VGA amplitude for zone 0 head 1 is AC.
The delta of VGA amplitudes for Zone 0 head 1 exceeds the limit (14)
The average VGA amplitude for zone 9 head 0 is BE.
The delta of VGA amplitudes for Zone 9 head 0 exceeds the limit (14)
The average VGA amplitude for zone 9 head 1 is B6.
The delta of VGA amplitudes for Zone 9 head 1 exceeds the limit (14)
The average VGA amplitude for zone F head 0 is 6C.
The delta of VGA amplitudes for Zone F head 0 exceeds the limit (14)
The average VGA amplitude for zone F head 1 is A3.
The delta of VGA amplitudes for Zone F head 1 exceeds the limit (14)

                        Power Cycling
ASCII logging off
OkEnd Test 22
Begin Test 61
OkEnd Test 61
Begin Test 28
ASCII logging on
OkEnd Test 4E
Begin Test 4E
ASCII logging off
ASCII logging on

                  Not Power Cycling
ASCII logging off
ASCII logging on
Log 02 - Health 2000 - HlthDtl 0000 - Time = 00:37:23 Log Type = 01
Log 82 - No Log on Disk
Log 83 - No Log on Disk
Log 84 - No Log on Disk
Log 03 - No Log on Disk
Log 73 - No Log on Disk
Log 05 - No Log on Disk
Log 06 - No Log on Disk
Log 07 - No Log on Disk
Log 0F - No Log on Disk
Log 10 - No Log on Disk
Log 11 - No Log on Disk
Log 12 - No Log on Disk
Log 13 - No Log on Disk
Log 14 - No Log on Disk
Log 15 - No Log on Disk
Log 16 - No Log on Disk
Log 17 - No Log on Disk
Log 18 - No Log on Disk
Log 19 - No Log on Disk
Log 1A - No Log on Disk
Log 1B - No Log on Disk
Log 1C - No Log on Disk
Log 1D - No Log on Disk
Log 1E - No Log on Disk
Log 2A - No Log on Disk
Log DA - No Log on Disk
Log DC - No Log on Disk
Log D6 - No Log on Disk
Log D7 - No Log on Disk
Log D8 - No Log on Disk
Log D9 - No Log on Disk
Log 56 - No Log on Disk
Log B0 - No Log on Disk
Log B1 - No Log on Disk
Log B2 - No Log on Disk
Log 0B - No Log on Disk
Log 7D - No Log on Disk
Log 58 - No Log on Disk
Log 08 - No Log on Disk
Log 0C - No Log on Disk
Log 0D - No Log on Disk
Log 40 - No Log on Disk
Log 31 - No Log on Disk
Log 32 - No Log on Disk
Log 33 - No Log on Disk
Log 34 - No Log on Disk
Log 36 - No Log on Disk
Log 37 - No Log on Disk
Log 26 - No Log on Disk
Log 3A - No Log on Disk
Log 0A - No Log on Disk
Log 8A - No Log on Disk
Log 3B - No Log on Disk
Log 3C - No Log on Disk
Log 3D - No Log on Disk
Log 3E - No Log on Disk
Log A9 - No Log on Disk
Log 3F - No Log on Disk
Log 09 - No Log on Disk
Log 20 - No Log on Disk
Log 77 - No Log on Disk
Log 43 - No Log on Disk
Log 27 - No Log on Disk
Log B3 - No Log on Disk
Log B4 - No Log on Disk
Log B5 - No Log on Disk
Log 51 - No Log on Disk
Log 48 - No Log on Disk
Log 41 - No Log on Disk
Log 49 - No Log on Disk
Log 4B - No Log on Disk
Log 4A - No Log on Disk
Log 4D - Health 0000 - HlthDtl 0000 - Time = 00:00:11 Log Type = 01
Log 39 - Health 0000 - HlthDtl 0000 - Time = 00:00:00 Log Type = 01
Log 22 - Health 0008 - HlthDtl 0003 - Time = 00:00:14 Log Type = 01
Log 61 - Health 0000 - HlthDtl 0000 - Time = 00:00:00 Log Type = 02
Log 28 - No Log on Disk
Log 62 - No Log on Disk
Log 29 - No Log on Disk
Log 63 - No Log on Disk
Log 59 - No Log on Disk
Log B6 - No Log on Disk
Log B7 - No Log on Disk
Log B8 - No Log on Disk
Log 6F - No Log on Disk
Total Cert Time = 00:37:48
ASCII logging off

                        Power Cycling
AbEnd Test 4E

T>Pgm=00 Trk=0006B(0006B[00B10]).0(0).0B7(FFF) Zn=0 Err=00 ErCt=0000 Hlth=2008 CHlth=2008 Ready LBA=09577DAC
Age=4F Type=A9 MxCyl=164F8 MxHd=1 MxSct=44C BSz=2000 TCode=00000000

作者: 毅然坚强 时间: 2008-7-2 09:11
这个是7代串口盘做SF的日志,,是哪个模块坏了导致没有SF LOG呢

作者: 火速挪移 时间: 2008-7-2 12:20
不是模块坏
是0头坏
建议换个固件F级开始做SF
如果还是这样故障
就能确定0头坏

作者: 毅然坚强 时间: 2008-7-2 16:26
固件全换吗??还是换某些模块呢

作者: 火速挪移 时间: 2008-7-2 17:41
全换固件

作者: 孤帆远影 时间: 2008-7-2 23:41
请问从LOG的那一部分看出是HEAD 0坏了
谢谢

作者: 火速挪移 时间: 2008-7-3 09:53

原帖由 孤帆远影 于 2008-7-2 23:41 发表

 登录/注册后看高清大图

请问从LOG的那一部分看出是HEAD 0坏了
谢谢

10楼里的0头很多43

作者: 李凤谋 时间: 2008-7-8 12:26
如果部分log没有呢？比如08以后的全没有该怎么解决呢？各位高手能否指点？

办法找到了，试验中~~~~~~~~~

[ 本帖最后由李凤谋于 2008-7-8 12:58 编辑 ]

欢迎光临迅维网 (https://www.chinafix.com/)